找回密码
 注册会员
更新自动建库工具PCB Footprint Expert 2024.04 Pro / Library Expert 破解版

[基础电路] 灯光控制系统电路,htControlSystem

[复制链接]
admin 发表于 2013-2-22 11:39:11 | 显示全部楼层 |阅读模式

本文包含原理图、PCB、源代码、封装库、中英文PDF等资源

您需要 登录 才可以下载或查看,没有账号?注册会员

×
灯光控制系统电路,ht Control System
  It is easy to install a couple of infrared emitter and receiver at the entrance of your room and maybe you connect them to the light, but you cannot control the light in this way! You will never know how many person inside and if the room is empty or not. In this system, every thing is under control, because it is smart enough to know how many persons inside; and it can identify the direction of them, so the light will be turned OFF when the room is unoccupied; and roundtrip="0">OP295 to produce the infrared beam, & two detectors in front of the emitter to detect the infrared beam OP598. Since the main idea in this device is to know person direction; and so, to get this approach, we have to use tow pieces of infrared detector in order to
   A
  DetectrorB
  Detector
  1
   High
  High
  2
   Low
  High
  3
   Low
  Low
  4
   High
  Low
  5
   High
  High
  
   Tip:If you have a camcorder, or just a camera mobile phone, you can see the infrared light! Just point the infrared emitter at the camera then you will be able to see the infrared light in the viewfinder. If you point your remote at the camera and push a button, you will see flashing light!
  
  identify the direction of the person as shown in Fig 2.
  
  When Infrared beam become broken ET280102010072110531512011060819483327703.png due to any body, the output signals from these detectors will be changed in unique sequence. Controller will identify the direction of the person by analyzing these signals as shown in the table at right "from 1 to 5 passed IN, 5 to 1 passed OUT":
  
  Since detectors output signals are analogue while the controller can roundtrip="0">LM393.
  
  Controller will increase the number of the persons in side the room by src="/data/attachment/portal/201007/ET28010201007211053152.png" border=0>
  
   ET280102010072110531532011060819483327704.png
  
  Notes:
  - You have to isolate detectors from any kind of light, except the infrared radiation.
  - Use TIP110 to drive relay current; it has Base-Emitter Shunt Resistors built in. Diode D1 is acting as a freewheeling diode.
  - Analogue reference voltage should be less than voltage produced by the detectors; otherwise, the system will not function properly . "Less than 0.1V is recommended"
  - The maximum speed of the body to be detected by the Light control System is 1.67 meter\second = 0.462 Km\Hour this value is accurate height=357 src="/data/attachment/portal/201007/ET28010201007211053154.png" width=359>
*滑块验证:
您需要登录后才可以回帖 登录 | 注册会员

本版积分规则

QQ|手机版|MCU资讯论坛 ( 京ICP备18035221号-2 )|网站地图

GMT+8, 2024-12-23 22:26 , Processed in 0.070837 second(s), 11 queries , Redis On.

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

快速回复 返回顶部 返回列表