找回密码
 注册会员
更新自动建库工具PCB Footprint Expert 2024.04 Pro / Library Expert 破解版

[基础电路] 汽车热限制器的烙铁AutoHeatLimiterforSolderingIron

[复制链接]
admin 发表于 2013-2-21 09:17:21 | 显示全部楼层 |阅读模式

本文包含原理图、PCB、源代码、封装库、中英文PDF等资源

您需要 登录 才可以下载或查看,没有账号?注册会员

×
汽车热限制器的烙铁 Auto Heat Limiter for Soldering Iron
  
  
  Wattage of load
  10W
  18W
  25W
  35W
  65W
  80W
  Value of R5 (in ohms)
  330
  180
  136 (68+68)
  100
  56
  44 (22+22)
  Wattage of R5 (in watts)
  01
  02
  02
  04
  05
  6.5
  
  
  Usually a soldering iron takes a couple of minutes to get adequately heated up to melt the solder, after which the heat generated is much above the requirement and is wasted. Moreover, excessive heat decreases the life of the bit and the element, causing serious damage to the components.
  
  The above circuit solves this problem in a simple and inexpensive way and could be used to various types of loads up to 80watts.
  
  How it works
  
  Once the main is switched on, an approximate 15v drop of the positive half cycle across R5 is detected and supplied to Q1 (SL100 or D313), which acts as a voltage regulator. Zener diode D2 together with diode D3 (yellow LED) stabilizes the emitter voltage of Q1 at 13.2Vdc, which is then delivered to the relay circuit built around Q2 and C3. Capacitor C3 charges through the base-emitter path of Q2 and causes the relay to actuate, which in turn allows both the half cycles of the AC mains to flow through diode D6 and R5 to the load to heat it up at a normal rate.
  
  After a certain lapse of time (about 2 minutes preset) C3 saturates and Q2 stops conducting through the relay, thus switching on series diode D5 to allow only half of the Ac cycle through the load.
  
  After switching off the system, C3 discharges very slowly through R2 and R3. Before C3 gets completely discharged, if the power is switched on again, C3 takes a shorter time to reach the saturation level, thus switching series diode D5 much earlier than the preset time to prevent double heating of the load.
  
  However, if the circuit is switched on only after a few seconds of switching off, C3 gets no time to discharge and the relay does not actuate at all. Moreover, if the relay circuit fails due to any reason and Q2 does not conduct, no hARM is done to the load because in that case D5 remains in series with it. Thus the circuit offers complete protection to the load.
  
  As stated earlier, the given value of C3 gives a delay of 2 minutes. However, a 1000mfd capacitor can also be used to produce a 4.5-minute delay. R5 maintains a drop of about 15V across itself. So for use in different load conditions its value changes as shown in Table 1.
  
  The whole circuit can be mounted on a PCB and fitted in an adapter case (7.6cm X 5.1cm X 6.4cm) and used as a mains plug. Since R5 gets heated up during the operation, it should be kept well isolated from the other components.
  
  
  Components List
  
  R1 - 220 ohms
  R2 ? 10K
  R3 ? 150K
  R4 ? 82K
  (all resistors should be 5% close tolerance)
  
  C1- 100 uf, 25V dc working electrolytic
  C2 ? 100 uf, 25V dc working electrolytic
  C3 ? 220 uf, 16V dc working electrolytic
  (advisable to use close tolerance Caps. to obtain correct timings)
  
  D1, D4, D5, & D6 ? IN4007
  D2 ? 12V 400mw, Zener diode
  D3 ? Yellow LED
  
  RLY1 ? 6V, 300 ohms DC relay
  Q1 ? SL100 or D313
  Q2 ? BC108
*滑块验证:
您需要登录后才可以回帖 登录 | 注册会员

本版积分规则

QQ|手机版|MCU资讯论坛 ( 京ICP备18035221号-2 )|网站地图

GMT+8, 2024-12-23 17:39 , Processed in 0.060660 second(s), 10 queries , Redis On.

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

快速回复 返回顶部 返回列表